Contacts
Technical documentation
+38(050)353-23-39
+38(044)502-23-38
+38(050)353-23-39
+38(044)502-23-38
Pumping of abrasive media, oils, petroleum products and liquids To 350°C.
To 2 000 m³/h.
To 40 bar
Pumping out air, saturated aggressive vapors, creating a vacuum To 33 mBar.
To 30 000 m³/h.
To 33 mbar.
Pumping air, saturated aggressive vapors, creating a vacuum To 5 mBar.
To 3 500 m³/h.
To 5 mbar
Pumping of liquids with different degrees of viscosity To 80,000 Cps To 250°C.
To 250 m³/h.
To 16 bar
Pumping of food products, wine and cosmetics industry.
To 200 m³/h.
To 16 bar
Pumping of foods with high viscosity and solid particles content.
To 20 m³/h.
To 12 bar
Pumping of aggressive chemicals, acids, alkalis and explosive liquids.
To 55 m³/h.
To 34 m H2O
Designed for stationary installation with direct immersion in the tank.
To 55 m³/h.
To 34 bar
Pumping liquids with different degrees of viscosity (glues, molasses, ointments, resins).
To 900 m³/h.
To 70 bar
Meat and dairy products, bakery products, pharmaceutical and chemical products.
To 70 m³/h.
To 15 bar
Accuracy better than 1% from 10 to 100% of maximum performance.
To 4028 m³/h.
To 80 bar
Highly viscous fluids that may contain high concentrations of solids/abrasives or other substances.
To 500 m³/h.
To 24 bar
Single-stage centrifugal pumps of petrochemical design TCD with CLOSED impeller for thermal oil
to 350 l/h.
to 10 bar.
Technical documentationEnvironment:
derived from
Standard: ISO 2858 / DIN 24256, ISO 5199.
Industry: chemical, petrochemical, pharmaceutical, food, pulp and paper, etc.
Impeller: radial closed type with cantilever installation.
Casing: volute type with axial flange on suction and discharge at 90°.
Shaft sealing: gland packing, single/double mechanical seal, special seal "SP".
Bearing support: specially designed with cooling fins to effectively dissipate heat from the pump casing so that the standard single mechanical seal can be safely used. Ensuring high reliability and minimal maintenance.
Material: ductile iron or stainless steel AISI 316. For the AISI 316 version, a special seal type “SP” can be used.
Option: heating/cooling chamber, cartridge seal, ATEX, MOSA version, etc.
Features: high efficiency efficiency and low NPSH in any application. Environmental, steel, textile industries, etc.
Special application: TCD is specially designed to work with coolants to 320˚C without special cooling systems. In the "XT" version with active cooling, diathermic liquids to 365 °C can be pumped.
Features: Derivative design spare parts from the TCH series reduce spare parts costs at reduced prices. The TCD/SP series of pumps has been specially developed for use with vegetable oils. The design differs from the standard TCD series only in the mechanical seal; an intermediate cover has been added outside the mechanical seal. This intermediate cover must be connected to a tank containing oil compatible with the pumped liquid. This device prevents air from entering the pump in the event of a mechanical seal failure, irreparably oxidizing the pumped oil, or oil from the bearings from entering the pump circuit, or vice versa.
Additional information: the heat from the pumped product is largely blocked by a special "thermal barrier" chamber located between the pump housing and the impeller.
The rotor is supported by large C3 series ball bearings, which are lubricated with medium viscosity oil.